武汉理工大学：《船舶辅机》课程教学资源（PPT课件，英文版）6.8 Instructions for DVZ-oily water separator

68 Instructions for DVz-oily water separator

6.8 Instructions for DVZ-oily water separator

6. 8 Instructions for dvz-oily water separator First set to operation Before putting into operation for the first time check that All connecting pipes and flanges specially on the suction side, are completely tight Air pressure is at 5-7bar The ship's voltage corresponds to that given on the type plate in the switch box or input transformer The supply from the ship's electrical system to the oily water separator's control system is connected -indicated by white lamp 2 mains Seawater is present in pipeline A2 All stop valves in pipelines to and from system are open

6.8 Instructions for DVZ-oily water separator • First set to operation Before putting into operation for the first time check that: • All connecting pipes and flanges specially on the suction side, are completely tight • Air pressure is at 5-7 bar • The ship's voltage corresponds to that given on the type plate in the switch box or input transformer • The supply from the ship's electrical system to the oily water separator's control system is connected-indicated by white lamp 2 “mains” • Seawater is present in pipeline A2 • All stop valves in pipelines to and from system are open

6.8 Instructions for DVZ-oily water separator · Attention: Seen from top-the pump must turn"left,, i.e. anti-clock-wise now. If not, the el. Motor 's supply has to be changed At left- turning pump the suction side is at A2. The pump now is sucking seawater via the opened non return flap a2. and is displacing it via pressure flange B2 into the separator The mano-vacuum gauge Pl. 2 shows the suction head from sea The non return flaps" A5.I andAl. 1 are closed; during the oil drain valve"A3. 1 is opened. The oily water separating system is bleeding automatically via the sludge oil tank. all this is automatically controlled by the sensing electrode" NI. Its sensing pins are surrounded by air

• Attention: – Seen from top-the pump must turn “left”, i.e. anti-clock-wise now. If not, the el. Motor’s supply has to be changed. At left￾turning pump the suction side is at A2. The pump now is sucking seawater via the opened non return flap A2.l and is displacing it via pressure flange “B2” into the separator. – The mano-vacuum gauge “Pl.2” shows the suction head from sea. The non return flaps “A5.l” and “A1.1” are closed; during the oil drain valve “A3.l” is opened. The oily water separating system is bleeding automatically via the sludge oil tank. All this is automatically controlled by the sensing electrode “N1”. Its sensing pins are surrounded by air. 6.8 Instructions for DVZ-oily water separator

6. 8 Instructions for dvz-oily water separator After first set to operation it takes some time until the air is bleeded from the separator and bilge suction pipe This is indicated by irregular lighting up the lamp oil to sludge tank After some time the system stabilizes automatically Under normal operating conditions more water than oil flows through separator. So it takes some time until the sensing electrode is surrounded by oil, because the oil buffer is growing from top to bottom. If surrounded by oil, the sensing electrode gives a signal via the niveau relay to the automatic switch box The valve"A3. 1 opens and the pump turns left, The pump is sucking from sea now and with that seawater the separated oil is pressed out to sludge tank via valve"A3. 1. During this state the non return valve a1. 1?' is dosed to avoid the back flow to bilge/bilge tank

6.8 Instructions for DVZ-oily water separator – After first set to operation it takes some time until the air is bleeded from the separator and bilge suction pipe. This is indicated by irregular lighting up the lamp “oil to sludge tank”. After some time the system stabilizes automatically. – Under normal operating conditions more water than oil flows through separator. So it takes some time until the sensing electrode is surrounded by oil, because the oil buffer is growing from top to bottom. If surrounded by oil, the sensing electrode gives a signal via the niveau relay to the automatic switch box. The valve “A3.l” opens and the pump turns “left”. The pump is sucking from sea now and with that seawater the separated oil is pressed out to sludge tank via valve “A3.l”. During this state the non return valve “A1.1” is dosed to avoid the back flow to bilge/bilge tank

6. 8 Instructions for dvz-oily water separator Worth of knowing Is the bilge/bilge tank emptied and the separator continues running- no problems will arise. It will be sucked air into the separator until the sensing electrode is surrounded by it. Now the pump turns over to scavenging from sea". The air is pressed out of the separator via valve"A3. 1" until the sensing electrode is surrounded by Water again. Now the unit turns over to "suction from bilge and so on When it should be forgotten to switch off the separator after emptying the bilge, by this means, the pump can not be destroyed by dry running

6.8 Instructions for DVZ-oily water separator • Worth of knowing Is the bilge/bilge tank emptied and the separator continues running-no problems will arise. It will be sucked air into the separator until the sensing electrode is surrounded by it. Now the pump turns over to "scavenging from sea". The air is pressed out of the separator via valve"A3.l" until the sensing electrode is surrounded by Water again. Now the unit turns over to "suction from bilge” and so on ..... • When it should be forgotten to switch off the separator after emptying the bilge, by this means, the pump can not be destroyed by dry running

Maintenance An oily water separator is not a main engine, the ships operation is not dependent from it, and the ship owners earn no profit with it. often an oil water separator is still estimated a necessary evil This is a false opinion The use of the oily water separator may protect the ship owner and ship crew getting fined, because of prohibited pollution of the sea from oil

Maintenance • An oily water separator is not a main engine, the ships operation is not dependent from it, and the ship owners earn no profit with it. Often an oily water separator is still estimated a necessary evil” This is a false opinion! The use of the oily water separator may protect the ship owner and ship crew getting fined, because of prohibited pollution of the sea from oil

Maintenance The nowadays problems on board of ships are well known to us from long years experience. This knowledge k you will find in the design of the Dvz-vo OILMASTER-System. The design and function are simple and robust the maintenance is limited to a minimum. From our experience from the past we know, that the most dvz-oily water separators make no problems if they are continuously running for long time Though the DVz-VC-OILMASTER" is designed very simple, from time to time it needs some"petting

Maintenance • The nowadays problems on board of ships are well￾known to us from long years experience. This knowledge you will find in the design of the DVZ - VC - "OILMASTER" - System. The design and function are simple and robust; the maintenance is limited to a minimum. From our experience from the past we know, that the most DVZ-oily water separators make no problems if they are continuously running for long time. Though the DVZ-VC-"OILMASTER" is designed very simple, from time to time it needs some “petting

The end of chapter 6

The end of chapter 6

Chapter 7 MARPOL 73/78 Regulations

Chapter 7 MARPOL 73/78- Regulations